Basler A400K Bedienungsanleitung Seite 36
- Seite / 130
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Physical Interface AW00118501000
28 Basler racer Camera Link
5.5 Camera Power
Power can be supplied to the camera in either one of two ways:
Via the base Camera Link SDR connector (Power over Camera Link).
Via the 6-pin connector (auxiliary power).
5.5.1 Supplying Power Over Camera Link
Power can be supplied to the camera via a Camera Link cable as specified in the Camera Link
standard v. 2.0 and above. This method of supplying power to the camera is known as Power over
Camera Link or PoCL. PoCL camera power can only be supplied via the base Camera Link SDR
connector.
The required nominal operating voltage for the camera is +12 VDC (± 10%) with less than one
percent ripple. For more details about PoCL power requirements, see the Camera Link
specifications v. 2.0 and above. Power consumption is as shown in the specification tables in
Section 1 of this manual.
The power for the camera is supplied by the connection to your frame grabber. Therefore, if you are
planning to use PoCL to power the camera, your frame grabber must be PoCL compliant.
NOTICE
If you are supplying power to the camera using PoCL:
1. The camera’s required nominal operating voltage is +12 VDC (± 10%), effective on the
camera’s connector.
2. Failure to use a Power over Camera Link compliant frame grabber can result in severe
damage to the camera.
3. Failure to use a Camera Link cable that is specifically designed for PoCL (as specified in the
Camera Link standard) can result in severe damage to the camera.
NOTICE
Making or breaking Camera Link connections incorrectly can cause severe damage to the
camera.
If you are supplying power to the camera via the Camera Link connection (PoCL), be sure that
the power to the camera and to the frame grabber in your PC is switched off before you connect
or disconnect the Camera Link cables.
- Basler racer 1
- Table of Contents 5
- 7 Pixel Formats and 6
- Basler racer Camera Link iii 7
- 1.1 Models 9
- 1.2 General Specifications 10
- 1.3 Spectral Response 11
- 1.4 Mechanical Specifications 12
- 1.4.2 Lens Adapter Dimensions 14
- Basler racer Camera Link 7 15
- 8 Basler racer Camera Link 16
- 1.7.2 Heat Dissipation 17
- 1.8 Precautions 18
- Basler racer Camera Link 11 19
- Warranty Precautions 20
- 2 Software and Hardware 21
- Installation 21
- 14 Basler racer Camera Link 22
- 3 Tools for Changing Camera 23
- Parameters 23
- 3.1.1 The pylon Viewer 24
- 3.1.2 The pylon API 24
- Basler racer Camera Link 17 25
- 18 Basler racer Camera Link 26
- 4 Camera Functional 27
- Description 27
- 5 Physical Interface 29
- 5.2.1 6-pin Receptacle 30
- 5.2.2 26-pin SDR Connectors 30
- 5.3 Connector Types 33
- 5.4 Cabling Requirements 34
- 5.4.2 Camera Link Cables 35
- 5.5 Camera Power 36
- Connector 37
- 5.5.3 LED Indicator 38
- 5.6.1 Inputs 39
- 5.6.1.2 Input Line Inverters 41
- the Line Start Trigger 42
- 5.6.2 Outputs 43
- 5.6.2.2 Output Line Inverters 45
- Basler racer Camera Link 41 49
- 6 Acquisition Control 51
- Exposure Time Control 52
- Basler racer Camera Link 45 53
- Basler racer Camera Link 47 55
- // rate internally 55
- 6.1.4.1 Introduction 56
- (duration determined by the 57
- Basler racer Camera Link 51 59
- 6.1.5.1 Introduction 60
- Timed exposure mode 61
- Trigger width exposure mode 61
- Trigger Width Exposure Mode 63
- 6.2 Frequency Converter 67
- 60 Basler racer Camera Link 68
- Basler racer Camera Link 61 69
- the exposure active signal 70
- 6.3.2 Acquisition Status 71
- Basler racer Camera Link 65 73
- 6.4 Maximum Allowed 74
- Line Acquisition Rate 74
- Basler racer Camera Link 67 75
- Basler racer Camera Link 69 77
- 70 Basler racer Camera Link 78
- Tap Geometries 79
- 7.2 Camera Link Tap Geometry 81
- 8 Features 83
- 76 Basler racer Camera Link 84
- 8.2 Gain and Black Level 85
- 8.2.1.1 Analog Gain 86
- 8.2.1.2 Digital Gain 87
- 80 Basler racer Camera Link 88
- // Set Gain Digital All 88
- 8.2.2 Black Level 89
- 8.3 Remove Parameter Limits 90
- 8.4.1 Setting the Image AOI 91
- Basler racer Camera Link 85 93
- 8.5 Luminance Lookup Table 94
- Using Basler pylon 96
- Using Direct Register Access 96
- 8.6 Binning 97
- 8.7 Gamma Correction 98
- Basler racer Camera Link 91 99
- 8.8 Shading Correction 100
- User Shading Set File 101
- Features AW00118501000 102
- 94 Basler racer Camera Link 102
- AW00118501000 Features 103
- Basler racer Camera Link 95 103
- 96 Basler racer Camera Link 104
- Basler racer Camera Link 97 105
- 8.9 Error Detection 106
- 8.9.2 Error Codes 107
- 8.10 Test Images 109
- 8.10.1 Test Images in Detail 110
- Basler racer Camera Link 103 111
- 8.12 User Defined Values 115
- 8.13 Configuration Sets 116
- Default Startup Set 117
- Set into the Active Set 118
- 112 Basler racer Camera Link 120
- 9 Troubleshooting and Support 121
- 9.3 Before Contacting Basler 122
- Technical Support 122
- 116 Basler racer Camera Link 124
- Revision History 125
- 118 Basler racer Camera Link 126
- AW00118501000 Index 127
- Basler racer Camera Link 119 127
- Index AW00118501000 128
- 120 Basler racer Camera Link 128
- Basler racer Camera Link 121 129
- 122 Basler racer Camera Link 130
Verwandte Produkte und Handbücher für Brückenkameras Basler A400K
Brückenkameras Basler A400K Bedienungsanleitung
(242 Seiten)
(242 Seiten)
Brückenkameras Basler A101f Bedienungsanleitung
(66 Seiten)
(66 Seiten)
Brückenkameras Basler A102f Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Brückenkameras Basler Camera Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Brückenkameras Basler A101f Bedienungsanleitung
(46 Seiten)
(46 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern